Zip-Strip Trigger Spray Paint & Finish Remover

Zip-Strip Trigger Spray Paint and Finish Remover is designed with easy application in mind. Its special formula sprays as a liquid so it penetrates into hard-to-get places like scrollwork, carving, spindles and filigree. Upon contact, Trigger Spray gels to a semi-paste consistency with clingability so it stays put, even on vertical surfaces. A fine initial spray begins the softening process. After five minutes spray a second time to activate further penetration, removing four to five coats or more. Zip-Strip Trigger Spray Paint and Finish Remover strips household paints and clear finishes, enamel, oil and latex paint, urethane, polyurethane, shellac, lacquer, water-based finish and spar varnish. It is non-flammable, and excellent for interior as well as exterior use. Just spray it on and remove with steel wool, a scraper or even wash off with water (Use of water may loosen veneer or raise wood grain. This would make it necessary to re-glue veneer or to sand the wood after it is thoroughly dry, prior to refinishing). Capable of removing 4-5 coats of paint.

Zip-Strip Industrial Paint & Finish Remover

Zip-Strip Industrial Paint and Finish Remover is the strongest of our removers and was developed for use on more difficult projects such as boats, cars and concrete. It contains a detergent which makes it possible to wash the finish off with water, minimizing scraping. The semi-paste consistency makes this remover a good choice for vertical as well as horizontal surfaces. Zip-Strip Industrial Paint and Finish Remover is non-flammable. It is excellent for interior as well as exterior applications. It removes eight or more coats of enamel, oil and latex paint, urethane, polyurethane, shellac, lacquer, water-based finish, varnish and even epoxy. It works well for marine, automotive, farm, and industrial applications including concrete swimming pools and metal lawn furniture. It will not raise the grain or discolor the wood. No neutralizing is required. Removes easily with a scraper, washing off with cool water and a scrub brush, or spraying with a high pressure stream of water. (Note: Use of water may loosen veneer or raise wood grain. This would make it necessary to re-glue veneer or to sand the wood after it is thoroughly dry, prior to refinishing.). Capable of removing up to 8 coats.

Zip-Strip Premium Paint & Finish Remover

Zip-Strip Premium Paint and Finish Remover is asked for by name more than any other paint and finish remover sold in the U.S. If you were to buy one remover to use on all of your projects, this would be the one. It has a non-flammable, semi-paste formula that works fast on vertical and horizontal surfaces. One application will remove five to six coats of enamel, oil and latex paint, urethane, polyurethane, shellac, lacquer, water-based finish and varnish. Zip-Strip Premium Paint and Finish Remover is suitable for interior as well as exterior applications. It will not raise the grain or discolor the wood. No neutralizing is required. It removes easily with a scraper, putty knife or steel wool. Capable of removing 5-6 coats.

Last-n-Last LNL-100SA Commercial Grade Oil-n-H2O Wood Floor Sealer

Last n Last LNL-100SA Commercial Grade Oil -n- H20 Wood Floor Sealer

LNL-100SA, is an ambering wood floor sealer featuring Oil·n·H2O™ technology. LNL-100SA is a low odor sealer, which penetrates the wood and dries quickly. LNL-100SA can be applied directly on stained wood surfaces, or on raw wood. When used under oil modified finish products, the sealer must be completely dry. Do not use over polyurethane, lacquer or other sealed surfaces. No Thinning Required.

RECOMMENDED USES:

Excellent for sealing most interior wood surfaces including floors, doors, cabinets, and furnitures.

TYPICAL PROPERTIES

Color in Container: Amber color(dries clear)

Solids Content: 25+/-1%

Chemical Resistance: Excellent

VOC: VOC does not exceed 275 grams/liter

Flash Point: 198°F

Pot Life: Unlimited in unopened container

Dry Time: 1 hour with good conditions

Clean Up: Water

Application method: T-Bar applicator, Synthetic waterborne applicator and nylon brush.

Coverage: 600-700 sq. feet per gallon.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:

New or Newly Sanded Floors or Wood Surfaces: Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of sealer should be a #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with water. The floor or work surface and room temperature should be at least 65°F.

APPLICATION:

Apply sealer using standard water based finish techniques. Applicator should be slightly dampened with sealer before starting. Pour sealer onto floor 4" strip along the starting wall. Apply the sealer with the grain of wood. applicator towards you holding the applicator at a slight “snowplow” angle. Remember keep a wet edge as you work. When you reach the end wall, pull the applicator in a sweeping motion, without lifting it from the floor. Feather turn, and gently touch any missed spots. Apply at recommended coverage. Screen with a #150 grit or maroon pad with gold strips prior to application of first top coat. Don’t over sand between coats.

Application over stain:

should adhere well to most stain, but a test for adhesion over brands other than Last•n•Last stain is recommended. Use Last•n•Last Classic Wood Stain following instruction on label. Allow the stain to dry a minimum of 24 hours under good conditions. Make sure the stain is completely dry before applying the finish or sealer. Not recommended under white or pastel stains.

Drying Time:

Last•n•Last 100 SA should be dry to the touch in 1 hour. Allow minimum of 2 hours before screening and for the topcoat to be applied. Heavy finish application, high humidity or lack of airflow will extend drying times. Under oil, longer dry time maybe needed.

Clean up:

Use water to clean brushes and applicators.

Lass-n-Last LNL-100S Commercial Grade Waterborne Wood Floor Sealer

Last n Last LNL-100S Commercial Grade Waterborne Wood Floor Sealer

LNL-100S is an advanced non-yellowing , low odor clear wood floor sealer which penetrates the wood and dries quickly. It can be applied directly on stained wood surfaces, or on raw wood. When used under oil modified finish products, the sealer must be completely dry. DO NOT USE OVER POLYURETHANE, LACQUER OR OTHER SEALED SURFACES. No Thinning Required.

RECOMMENDED USES:

Excellent for sealing most interior wood surfaces, including floors, doors, cabinets, and furnitures.

TYPICAL PROPERTIES

Color in Container: Milky white (dries clear)

Solids Content: 25+/-1%

Chemical Resistance: Excellent

VOC: VOC does not exceed 275 grams/liter

Flash Point: 198°F

Pot Life: Unlimited in unopened container

Dry Time: 1 hour with good conditions

Clean Up: Water

Application method: T-Bar applicator, Synthetic waterborne applicator and nylon brush.

Coverage: 600-700 sq. feet per gallon.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear properprotection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:

New or Newly Sanded Floors or Wood Surfaces: Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of sealer should be a #100 to #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with water. The floor or work surface and room temperature should be at least 65°F.

APPLICATION:

Apply sealer using standard water based finish techniques. Applicator should be slightly dampened with finish before starting. Pour sealer onto floor 4" strip along the starting wall. Apply the sealer with the grain of wood. Pull the applicator towards you holding it at a slight “snowplow” angle. Remember to keep a wet edge as you work. When you reach the end wall, pull the applicator in a sweeping motion, without lifting it from the floor. Feather turn, and gently touch any missed spots. Apply at recommended coverage, in thin coats.

Drying Time:

Last•n•Last 100 S should be dry to the touch in 1 hour. Allow minimum of 1 hours before screening and for the topcoat to be applied. Heavy finish application, high humidity or lack of airflow will extend drying times.

Clean up:

Use water to clean brushes and applicators.

Last-n-Last LNL-1500 Commercial Grade Waterborne Wood Floor Finish

Last n Last LNL-1500 Commercial Grade Waterborne Wood Floor Finish

LNL-1500 Commercial Wood Floor Finish incorporates Aluminum Oxide, Microban antimicrobial protection, and UV absorbers in a single component non-yellowing urethane finish. Featuring a 15 Year Residential Wear Warranty, LNL1500 will prove superior durability, with the added benefits of low odor, fast dry time and easy cleanup Microban® protection continuously inhibits the growth of bacteria, mold and mildew that can cause stains, odors, and damage the finish on your floor. And because Microban® protection is built into this coating, it will not wash off or wear away for the life of the finish.

RECOMMENDED USES:

Last•n•Last 1500 Wood Floor Finish is recommended for interior residential application.

TYPICAL PROPERTIES

Color in Container: Milky white (Dries clear)

Solids Content: 32+/-1%

Chemical Resistance: Excellent

VOC:VOC does not exceed 275grams/liter

Flash Point 198°F

Sheen Gloss: >80 units @ 60° on wood

Semi-Gloss: 50-60 units @ 60° on wood

Satin: 25-30 units @ 60° on wood

Freeze/Thaw Stability: Stable (if frozen, thaw completely before using)

Pot Life: Unlimited in unopened container

Dry Time: 2 to 3 hours with good conditions

Clean Up: Water

Application method: T- bar applicator, Synthetic waterborne applicator and nylon brush.

Coverage: 400-450 sq. feet per gallon.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:

New or Newly Sanded Floors or Wood Surfaces:Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of Last•n•Last 1500 and sealer should be a #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with water. The floor or work surface and room temperature should be at least 65°F.

Previously finished Floors or Wood Surfaces: Remove old finish in poor condition. If the old finish is shellac or contains wax or any stearate, regardless of the condition, remove it completely then follow surface preparation for New Wood Surfaces. If old finish is still sound and good, screen the work surface with a #150 screen disc, #180 grit sand paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming and wiping the work surface with a lint free cloth lightly dampened with water. The work surface and room temperature should be at least 65°F. Two to three coats work best on previously finished surfaces.

REMEMBER TO STIR THIS PRODUCT BEFORE AND DURING USE. LET IT STAND FOR 10 MINUTES AFTER STIRRING.

Application:

Apply in well ventilated area by nylon brush, or synthetic waterborne applicator at room temperature and not in direct sunlight. Last•n•Last 1500 looks milky when applied, but will dry to a clear, beautiful finish. Pou a 6-8” wide line of the finish along the starting wall. Apply the finish with the grain of the wood. Using a clean pre-dampened waterborne applicator, pull forward with the grain of the wood, moving the finish towards the opposite wall. Holding the applicator at a snowplow angle will maintain a wet edge at all times.( Maintain at least 3” wide wet edge to ensure proper coverage). At the end of each run, turn the applicator towards you and pad out the applicator parallel to the wet edge. Feather out turns. If pushed too hard or fast, drips will fly off the applicator. Missed areas can be touched up if seen right away. To prevent lapping and dry marks, be sure you are using the recommend coverage. Do no spread too thin. Screen the work surface in between coats with any of the following #150 screen disc, #180 grit sand paper, maroon pad or similar. Remember to vacuum and tack thoroughly after screening to remove all dust. Allow minimum of two hours between coats, or until thoroughly dry. Heavy finish application, high humidity or lack of airflow will extend drying times. If waiting longer than 24 hours between coats, sanding is recommended.

Application over stain: Last•n•Last 1500 should adhere well to most stain, but a test for adhesion over brands other than Last•n•Last stain is recommended. Use Last•n•Last Classic Wood Stain following instruction on label. Allow the stain to dry a minimum of 24 hours under good conditions. Make sure the stain is completely dry before applying the finish or sealer.

Drying Time:

When applied according to directions, and in thin coats, Last•n•Last 1500 should be dry to the touch in 1 hour. Allow minimum of 2 hours between coats. Heavy finish application, high humidity or lack of airflow will extend drying times. Last•n•Last 1500 completely cures within 2 weeks. Please allow the finish to be fully cured for area rugs or mats to be put down. The floor is susceptible to scuffing and marring before full cure.

Clean up:

Use water to clean brushes and applicators.

Maintenance:

Last•n•Last 1500 never needs waxing. We recommend Polycare Floor Cleaner as the safe and effective cleaning product for all polyurethane coated surfaces. It has a unique soap-free, no rinse formula which will not harm polyurethane or varnished wood surfaces.

Last-n-Last TREK PLUS Commercial Grade Waterborne Floor Finish

Last n Last TREK PLUS Commercial Grade Waterborne Floor Finish

Trek Plus Commercial Wood Floor Finish incorporates Aluminum Oxide in a two-part non-yellowing urethane finish to provide unmatched durability and wear. Featuring a 15-year Residential Wear Warranty, Trek Plus will exceed moisture cure for toughness, with the added benefits of low odor, fast dry time and easy cleanup.

RECOMMENDED USES:

Interior wood surfaces.

TYPICAL PROPERTIES

Color in Container: Milky white (dries clear)

Solids Content: 33-34%

Chemical Resistance: Excellent

VOC: VOC does not exceed 275 grams/liter

Flash Point: 198°F

Sheen Gloss: >80 units @ 60° on wood

Semi-Gloss: 50-60 units @ 60° on wood

Satin: 25-30 units @ 60° on wood

Freeze/Thaw Stability: Stable (if frozen, thaw completely before using)

Pot Life:Unlimited in unopened container

Dry Time: 2 to 3 hours with good conditions

Clean Up: Water

Application method: T-bar applicator, Synthetic waterborne applicator, Nylon brush.

Coverage:400-450 sq. feet per gallon.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:

New or Newly Sanded Floors or Wood Surfaces: Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of Last•n•Last Trek Plus and sealer should be a #100 to #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with water. The floor or work surface and room temperature should be at least 65°F.

Previously Fiinished Wood Surfaces: Remove old finish in poor condition. If the old finish is shellac or contains wax or any stearate, regardless of the condition, remove it completely then follow surface preparation for New Wood Surfaces. If old finish is still sound and good, screen the work surface with a #150 screen disc, #180 grit sand paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming and wiping the work surface with a lint free cloth lightly dampened with water. The work surface and room temperature should be at least 65°F. Two to three coats work best on previously finished surfaces. To achieve a beautiful High Gloss Finish, we recommend 2 coats of Trek Plus Satin followed by one coat of Trek Plus Gloss. To achieve a beautiful Semigloss Finish, we recommend 2 coats of Trek Plus Satin followed by one coat of Trek Plus Semigloss. Sand between coats of Trek Plus Satin with a maroon pad with 220 grit sandpaper strips, and don’t abrade prior to the final coat of Trek Plus Gloss or semigloss. Sealer XL may replace the first coat of finish on unfinished wood.

REMEMBER TO STIR THIS PRODUCT BEFORE AND DURING USE. LET IT STAND FOR 10 MINUTES AFTER STIRRING.

Application:

Apply in well ventilated area by nylon brush, or synthetic waterborne applicator at room temperature and not in direct sunlight.For unstained floor, Sealer XL may be applied followed by The Trek Plus finish. Do not use Sealer XL if floor is to be stained. Last•n•Last Trek Plus looks milky when applied, but will dry to a clear, beautiful finish. Pou a 6-8” wide line of the finish along the starting wall. Apply the finish with the grain of the wood. Using a clean pre-dampened waterborn applicator, pull forward with the grain of the wood, moving the finish towards the opposite wall. Holding the applicator at a snowplow angle will maintain a wet edge at all times. Maintain at least 3” wide wet edge to ensure proper coverage). At the end of each run, turn the applicator towards you and pad out the applicator parallel to the wet edge. Feather out turns. If pushed too hard or fast, drips will fly off the applicator. Missed areas can be touched up if seen right away.To prevent lapping and dry marks, be sure you are using the recommendd overage. Do no spread too thin. Screen the work surface in between coats with any of the following #150

screen disc, #180 grit sand paper, maroon pad or similar. Remember to vacuum and tack thoroughly after screening to remove all dust. Allow minimum of two hours between coats, or until thoroughly dry. Heavy finish application, high humidity or lack of airflow will extend drying times. If waiting longer than 24 hours between coats, sanding is recommended.

Application over stain: Last•n•Last Trek Plus should adhere well to most stain, but a test for adhesion over brands other than Last•n•Last stain is recommended. Use Last•n•Last Classic Wood Stain following instruction on label. Allow the stain to dry a minimum of 24 hours under good conditions. Make sure the stain is completely dry before applying the finish. Do not use sealer if a stain is to be used.

Drying Time:

When applied according to directions, and in thin coats, Last•n•Last Trek Plus should be dry to the touch in 1 hour. Allow minimum of 2 hours between coats. Heavy finish application, high humidity or lack of airflow will extend drying times. Last•n•Last Trek Plus completely cures within 2 weeks. Please allow the finish to be fully cured for area rugs or mats to be put down. The floor is susceptible to scuffing and marring before full cure.

Clean up:

Use water to clean brushes and applicators.

Maintenance:

Last•n•Last Trek Plus never needs waxing. We recommend Polycare Floor Cleaner as the safe and effective cleaning product for all polyurethane coated surfaces. It has a unique soap-free, no rinse formula which will not harm polyurethane or varnished wood surfaces.

Last-n-Last Grand Oil-n-H20 Wood Floor Finish

Last n Last Grand Oil-n-H20 Wood Floor Finish

Absco Grand Wood Floor Finish is the newest generation of state-of-the art wood floor finishes for the professional. Absco grand combines the most advanced waterbased technology with oil-modified polyurethane for beauty and durability. Featuring Oil•n•water, 100% urethane technology, Absco Grand needs no separate crosslinker to provide tough protection for wood floors. No thinning required.

RECOMMENDED USES:

Absco grand Wood Floor Finish is recommended for interior residential wood.

Not recommended for white or light stained floor.

TYPICAL PROPERTIES

Color in Container: Yellowish white (Dries clear)

Solids Content: 30+/-1%

Chemical Resistance: Excellent

VOC: VOC does not exceed 275grams/liter

Flash Point: 198°F

Sheen Gloss: >80 units @ 60° on wood

Semi-Gloss: 50-60 units @ 60° on wood

Satin: 25-30 units @ 60° on wood

Freeze/Thaw Stability: Stable (if frozen, thaw completely before using)

Shelf Life: Unlimited in unopened container

Dry Time :2 hours under good conditions

Clean Up: Water

Application method: T-bar applicator, Synthetic waterborne applicator and nylon brush.

Coverage: 500-550 sq. feet per gallon.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:

New or Newly Sanded Floors or Wood Surfaces: Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of Absco Grand and sealer should be a #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with water. The floor or work surface and room temperature should be at least 65°F.

Previously Finished Floors or Wood Surfaces:Remove old finish in poor condition. If the old finish is shellac or contains wax or any stearate, regardless of the condition, remove it completely then follow surface preparation for New Wood Surfaces. If old finish is still sound and good, screen the work surface with a #150 screen disc, #180 grit sand paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming and wiping the work surface with a lint free cloth lightly dampened with water. The work surface and room temperature should be at least 65°F.

REMEMBER TO STIR THIS PRODUCT BEFORE AND DURING USE. LET IT STAND FOR 10 MINUTES AFTER STIRRING.

Application:

Apply in well ventilated area by nylon brush, or synthetic waterborne applicator at room temperature and not in direct sunlight. Slightly dampen applicator with finish prior to starting. Pour finish onto floor in a 4” strip along the starting wall. Apply finish with the grain of the wood. Pull the applicator towards you at a slight “snowplow” angle. Remember to keep a wet edge as you work. Feather all turns and stops in the direction which the applicator was pulled. When you reach the end wall, pull the applicator around in a sweeping motion, without lifting it from the floor. Feather turn, and gently touch any missed spots. Apply at recommended coverage in thin coats.

Application over stain: Absco Grand should adhere well to most stain, but a test for adhesion over brands other than Last•n•Last stain is recommended. Use Last•n•Last Classic Wood Stain following instruction on label. Allow the stain to dry a minimum of 24 hours under good conditions. Make sure the stain is completely dry before applying the finish or sealer.

Drying Time:

When applied according to directions, and in thin coats, Absco Grand should be dry to the touch in 1 hour. Allow minimum of 2 hours between coats. Heavy finish application, high humidity or lack of airflow will extend drying times. Abscp Grand completely cures within 2 weeks. Please allow the finish to be fully cured for area rugs or mats to be put down. The floor is susceptible to scuffing and marring before full cure.. No more than two coats are recommended per day.

Clean up:

Use water to clean brushes and applicators.

Maintenance:

Absco Grand never needs waxing. We recommend Polycare Floor Cleaner as the safe and effective cleaning product for all polyurethane coated surfaces. It has a unique soap-free, no rinse formula which will not harm polyurethane or varnished wood surfaces.

Last-n-Last Marine and Door Spar varnish Oil-n-H20 Technology

Last n Last Marine and Door Spar varnish Oil-n-H20 Technology

Last-n-Last Marine and Door Spar Varnish will provide outstanding protection for all types of exterior woodwork. Formulated to resist mold and mildew, Last•n•Last Marine & Door Spar Varnish is the clear choice for exterior wood protection . It incorporates the latest Oil• n• H20 technology, which will provide superior durability, fast dry times and soap & water clean-up. It will provide outstanding beauty and durability. It contains UV absorbers for long lasting sun protection. Adhesion is excellent – resists flaking and chipping. Not recommended for decks of siding.

RECOMMENDED USES:

Last•n•Last Marine & Door Spar Varnish is recommended for exterior doors, trims, windowsills, outdoor furnitures, wooden boat parts above the water line.

TYPICAL PROPERTIES

Color in Container: Yellowish white (Dries clear)

Solids Content: 30+/-1%

Chemical Resistance: Excellent

VOC: VOC does not exceed 275grams/liter

Flash Point: 198°F

Sheen Gloss: >80 units @ 60° on wood

Satin: 55-60 units @ 60° on wood

Freeze/Thaw Stability Stable (if frozen, thaw completely before using)

Pot Life Unlimited in unopened container

Dry Time: 2 hours with good conditions

Clean Up: Water

Application method: Nylon brush

Coverage: 400-500 sq. feet per gallon.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:

New or Newly Sanded Wood Surfaces: Make several passes with the sandpaper, increasing the paper fineness with each pass. The final pass before application of Last•n•Last Marine and door spar varnish should be with a #100 to #150 grit screen pad or sandpaper. Remove dust completely

by sweeping, vacuuming and wiping the work surface with a lint free cloth lightly dampened with water. The work surface and room temperature should be at least 65°F.

Previously Finished Wood Surfaces:

Remove old finish in poor condition. Screen the work surface with #180 grit sand paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming and wiping the work surface with a lint free cloth lightly dampened with water. The work surface and room temperature should be at least 65°F.

Application:

Apply the finish with the grain of the wood. Apply in well ventilated area with a good quality brush . Avoid applying the finish in direct sunlight or let the uncured coating be exposed to moisture. Screen the work surface in between coats with any of the following #180 grit sand paper, maroon pad or similar in between coats. Remember to vacuum and tack thoroughly after screening to remove all dust. Allow minimum of two hours between coats, or until thoroughly dry. Heavy finish application, high humidity or lack of airflow will extend drying times. If waiting longer than 24 hours between coats, sanding is recommended. A minimum of 4 is recommended on unsealed wood; 3-4 coats on previously sealed wood.

Drying Time:

When applied according to directions, and in thin coats, Last•n•Last Marine & Door Spar varnish should be dry to the touch in 1 hour. Allow minimum of 2 hours between coats. Heavy finish application, high humidity or lack of airflow will extend drying times. Last·n·Last Marine & Door Spar varnish completely cures within 2 weeks.

Clean up:

Use water to clean brushes and applicators.

Maintenance:

We recommend to recoat it periodically depending on the harshness of the outdoor conditions. We recommend Polycare Cleaner as the safe and effective cleaning product for all polyurethane coated surfaces. It has a unique soap-free, no rinse formula which will not harm polyurethane or varnished wood surfaces.

XIM Bonding Primer

XIM introduces 400 NT 100. This bonding primer maintains the bonding characteristics of 400W while an evolved formulation using exempt solvents and resin modifications lowers the VOC content of the product down to 100 g/l. 400W NT 100 primes regular surfaces and hard-too-paint surfaces such as glass, tile, fiberglass, plastics, etc. 400 W NT 100 can be used with all topcoats by allowing it to cure slightly longer for strong solvent coats.

Zinsser Bull Eye Zero and Bull Eye Shellac

Zinsser Bull Eye Zero is an interior/exterior primer that delivers premium performance with out volatile organic compounds (VOCs). It offers "best in class" performance in an eco-friendly, LEED compliant formula that's great for all interior and exterior surfaces. Fast drying and low odor, it offers superior stain blocking properties, a mildew-resistant film with great enamel holdout and legendary Zinsser adhesion.

Zinsser Bull Eye Shellac has been making good look beautiful since 1849, giving it rich warmth, depth and clarity that enhances its natural beauty like no polyurethane or other synthetic finishes. If won't yellow or darken with age. Bulls Eye Shellac is all-natural and non-toxic when dry, so it's an ideal versatile, environmentally  friendly for wood finishing

Last-n-Last Ultra Gold Oil•n•Water Wood Finish

Last n Last Ultra Gold Oil•n•Water Wood Finish
LNL Ultra Gold incorporates the latest Oil·n·H2O technology with Microban antimicrobial protection, for advanced protection of all interion wood surfaces. Our unique Oil·n·H2O, 100% urethane technology, is incredibly easy to use, and provides beautiful long lasting protection to all types of wood. Ultra Gold is designed to be used on all types of wood, including floors, stairs, moldings, furniture, and crafts. No thinning required. Not recommended for white stained wood. Microban protection continuously inhibits the growth of bacteria, mold and mildew that can cause stains, odors,
and damage the finish on your floor. And because Microban protection is built into this coating, it will not wash off or wear away for the life of the finish.

RECOMMENDED USES:
LNL Ultra Gold is recommended for interior residential wood.

TYPICAL PROPERTIES
Color in Container: Yellowish white (Dries clear)
Solids Content: 30+/-1%
Chemical Resistance: Excellent
VOC: VOC does not exceed 275grams/liter
Flash Point: 198°F
Sheen Gloss: >80 units @ 60° on wood
Semi-Gloss: 50-60 units @ 60° on wood
Satin: 25-30 units @ 60° on wood
Freeze/Thaw Stability Stable: (if frozen, thaw completely before using)
Shelf Life: Unlimited in unopened container
Dry Time: 2 hours under good conditions
Clean Up: Water
Application method: Synthetic waterborne applicator and nylon brush.
Coverage: 500-550 sq. feet per gallon.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:
New or Newly Sanded Floors or Wood Surfaces:Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of Last•n•Last Ultra Goldand sealer should be a #100 to #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with water. The floor or work surface and room temperature should be at least 65°F.

Previously Finished Floors or Wood Surfaces:Remove old finish in poor condition. If the old finish is shellac or contains wax or any stearate, regardless of the condition,remove it completely then follow surface preparation for New Wood Surfaces. If old finish is still sound and good, screen the work surface with a #100 to #150 screen disc, #180 grit sand paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming and wiping the work surface with a lint free cloth lightly dampened with water. The work surface and room temperature should be at least 65°F.

REMEMBER TO STIR THIS PRODUCT BEFORE AND DURING USE. LET IT STAND FOR 10 MINUTES AFTER STIRRING.

Application:
Apply Ultra Gold with the grain of the wood using long even strokes.

Application on Floors: Apply in well ventilated area by nylon brush, or synthetic waterborne applicator at room temperature and not in direct sunlight. Slightly dampen applicator with finish prior to starting. Pour finish onto floor in a 4” strip along the starting wall. Apply finish with the grain of the wood. Pull the applicator towards you at a slight “snowplow” angle. Remember to keep a wet edge as you work. Feather all turns and stops in the direction which the applicator was pulled. When you reach the end wall, pull the applicator around in a sweeping motion, without lifting it from the floor. Feather turn, and gently touch any missed spots. Apply at recommended coverage in thin coats.

Application over stain: Last•n•Last Ultra Gold should adhere well to most stain, but a test for adhesion over brands other than Last•n•Last stain is recommended. Use Last•n•Last Classic Wood Stain following instruction on label. Allow the stain to dry a minimum of 24 hours under good conditions. Make sure the stain is completely dry before applying the finish or sealer.

Drying Time:
When applied according to directions, and in thin coats, should be dry to the touch in 1 hour. Allow minimum of 2 hours between coats. Heavy finish application, high humidity or lack of airflow will extend drying times. Last•n•Last Ultra Gold completely cures within 2 weeks. Please allow the finish to be fully cured for area rugs or mats to be put down. The floor is susceptible to scuffing and marring before full cure.. No more than two coats are recommended per day.

Clean up:
Use water to clean brushes and applicators.

Maintenance:
Last•n•Last Ultra Gold never needs waxing. We recommend Polycare Floor Cleaner as the safe and effective cleaning product for all polyurethane coated surfaces. It has a unique soap-free, no rinse formula which will not harm polyurethane or varnished wood surfaces.

Last-n-Last Absco Polyurethane Wood Floor Finish 450-VOC

Last-n-Last Absco Polyurethane Wood Floor Finish 450-VOC
ABSCO Professional Polyurethanes offers the latest technology in environmentally compliant wood floor finishes. ABSCO’s high solid content will beautify and protect most commercial and residential wood floors, providing years of enjoyment. ABSCO can also offer superior protection to most other interior wood surfaces, such as handrails, trim, furniture and cabinets.

RECOMMENDED USE
Absco Polyurethane Wood Floor Finish is recommended for most interior commercial and residential wood.

TYPICAL PROPERTIES
Color in Container :Gloss - Clear / Satin - Hazy/ Semi-Gloss – Hazy
Solids Content/weight: Gloss – 50% / Satin – 51% / Semi-Gloss – 51%
Chemical Resistance: Excellent
VOC: VOC does not exceed 450 grams/liter
Flash Point: 105°F
Sheen Gloss: No less than 90 units on wood.
Satin: 25-35 units on wood.
Semi-Gloss: 50-60 units on wood.
Freeze/Thaw Stability: Stable
Shelf Life: Unlimited in unopened container.
Drying Time: 12 hrs. under good condition.
Cleanup: Mineral Spirits, Paint Thinner, Turpenine.
Application method: Lambswool applicator, natural bristle brush or E-Z Way Applicator.
Coverage Approx: 500-600 sq feet per gallon on raw wood.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:
New or Newly Sanded Floors or Wood Surfaces: Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of Absco Polyurethane Wood Floor Finish and sealer should be a #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with mineral spirits. Avoid using fillers that contain stearates or wax. The floor or work surface and room temperature should be at least 65°F.

Previously Finished Floors or Wood Surfaces: Remove old finish in poor condition. Screen the work surface with a #150 screen disc, #180 grit sand paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with mineral spirits. Avoid using fillers that contain stearates or wax.The floor or work surface and room temperature should be at least 65°F.

REMEMBER TO STIR THIS PRODUCT BEFORE AND DURING USE. SATIN AND SEMI-GLOSS CAN BE SHAKEN. AFTER SHAKING, LET IT SIT FOR 10 MINUTES.

Application:
Apply the finish with the grain of the wood. Apply in well ventilated area by brush, roller, spray, EZ way, lambswool applicator at room temperature and not in direct sunlight. When using a roller, work slowly to avoid air bubbles. Screen the floor or work surface in between coats with any of the following #150 screen disc, #180 grit sand paper, maroon pad or similar in between coats. Remember to vacuum and tack thoroughly after screening to remove all dust. Allow minimum of four to eight hours between coats, or until thoroughly dry. Heavy finish application, high humidity or lack of airflow will extend drying times. If waiting longer than 24 hours between coats, sanding is recommended.

Application over stain:Absco Polyurethane Wood Floor Finish should adhere well to most stain. A test for adhesion over brands other than Last•n•Last stain is recommended. Use Last•n•Last Classic Wood Stain following instruction on label. Allow the stain to dry a minimum of 24 hours under good conditions. Make sure the stain is completely dry before applying the Finish. Drying time: When applied according to directions, and in thin coats, Absco Polyurethane Wood Floor Finish should be dry to the touch in 4-6 hrs. Allow minimum of 12 hours between coats. Heavy finish application, high humidity or lack of airflow will extend drying times. Absco Polyurethane Wood Finish completely cures within 2 weeks.

Clean up:
Use paint thinner, mineral spirits or turpentine to clean brushes and applicators.

Maintenance:
Absco Polyurethane Wood Floor Finish never needs waxing. We recommend Polycare Floor Cleaner as the safe and effective cleaning product for all polyurethane coated surfaces. It has a unique soap-free, no rinse formula which will not harm polyurethane or varnished wood surfaces.

Last-n-Last Absco Polyurethane Wood Floor Finish 550 VOC

Last n Last Absco Polyurethane Wood Floor Finish 550 VOC
ABSCO Professional Polyurethanes offers the latest technology in environmentally compliant wood floor finishes. ABSCO’s high solid content will beautify and protect most commercial and residential wood floors, providing years of enjoyment. ABSCO can also offer superior protection to most other interior wood surfaces, such as handrails, trims, furnitures and cabinets.

RECOMMENDED USES:
Absco Polyurethane Wood Floor Finish is recommended for most interior
commercial and residential wood.

TYPICAL PROPERTIES
Color in Container: Gloss - Clear ; Satin – Hazy; Semi-Gloss – Hazy
Solids Content/weight: Gloss – 50% ; Satin – 39% ; Semi-Gloss – 42%
Solids Content/volume: Gloss – 47% ; Satin – 36% ; Semi-Gloss – 39%
Chemical Resistance: Excellent
VOC: VOC does not exceed 550 grams/liter
Flash Point: 105°F
Sheen Gloss: No less than 90 units on wood.
Satin: 25-35 units on wood.
Semi-Gloss: 50-60 units on wood.
Freeze/Thaw Stability: Stable
Shelf Life: Unlimited in unopened container.
Drying Time: 4-6 hrs. under good conditions .
Cleanup: Mineral Spirits, Paint Thinner, Turpentine
Application method: Lambswool applicator, natural bristle brush or E-Z Way Applicator.
Coverage Approx: 500-600 sq feet per gallon on raw wood.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:
New or Newly Sanded Floors or Wood Surfaces:Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of Absco Polyurethane Wood Floor Finish and sealer should be a #100 to #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with mineral spirits. Avoid using fillers that contain stearates or wax. The floor or work surface and room temperature should be at least 65°F.

Previously Finished Floors or Wood Surfaces:Remove old finish in poor condition. Screen the work surface with a #100 to #150 screen disc, #180 grit sand paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with mineral spirits. Avoid using fillers that contain stearates or wax. The floor or work surface and room temperature should be at least 65°F.

REMEMBER TO STIR THIS PRODUCT BEFORE AND DURING USE. SATIN AND SEMI-GLOSS CAN BE SHAKEN. AFTER SHAKING, LET IT SIT FOR 10 MINUTES.

Application:
Apply the finish with the grain of the wood. Apply in well ventilated area by brush, roller, spray, EZ-way applicator or lambswool applicator at room temperature and not in direct sunlight. When using a roller, work slowly to avoid air bubbles. Screen the floor or work surface in between coats with any of the following #100 to #150 screen disc, #180 grit sand paper, maroon pad or similar in between coats. Remember to vacuum and tack thoroughly after screening to remove all dust. Allow a minimum of six hours between coats, or until thoroughly dry. Heavy finish application, high humidity or lack of airflow will extend drying times. If waiting longer than 24 hours between coats, sanding is recommended.

Application over stain: Absco Polyurethane Wood Floor Finish should adhere well to most stain. If a stain other than Last•n•Last is to be used, a test for adhesion is recommended. Use Last•n•Last Classic Wood Stain following instruction on label. Allow to dry a minimum of 24 hours under good conditions. Make sure the stain is completely dry before applying the Finish.

Drying Time:
When applied according to directions, and in thin coats, Absco Polyurethane Wood Floor Finish should be dry to the touch in 4 to 6 hours. Allow minimum of 6 hours between coats. Heavy finish application, high humidity or lack of airflow will extend drying times. Absco Polyurethane Wood Finish completely cures within 2 weeks.

Clean up:
Use paint thinner, mineral spirits or turpentine to clean brushes and applicators.

Maintenance:
Absco Polyurethane Wood Floor Finish never needs waxing. We recommend Polycare Floor Cleaner as the safe and effective cleaning product for all polyurethane coated surfaces. It has a unique soap-free, no rinse formula which will not harm polyurethane or varnished wood surfaces.

Last-n-Last Absco Quick Dry Polyurethane Primer-Sanding Sealer-500 VOC

Last n Last Absco Quick Dry Polyurethane Primer / Sanding Sealer-500 VOC
Absco Professional Quick Dry Polyurethane Primer Sealer offers the latest technology in environmentally compliant wood floor sealers. Absco’s high solid content will seal wood surfaces with 100% polyurethane protection, and will be ready to sand in as little as 2 hours when applied according to directions.

RECOMMENDED USES:
Excellent for sealing most interior wood surfaces, including floors, doors, cabinets & furnitures.

TYPICAL PROPERTIES
Color in Container: Amber
Solids Content Weight: 43-44%
Chemical Resistance: Excellent
VOC: Does not exceed 500 g/l
Flash Point: 105°F
Sheen: Not Applicable
Freeze/Thaw Stability Stable
Dry Time:2 hours under good conditions
Clean Up: Mineral Spirits, Paint Thinner, Turpentine
Shelf Life: Unlimited in unopened container.
Application method: Lambswool applicator, natural bristle brush, and EZ way Applicator
Coverage: 550-650 sq. feet/gal

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:
New or Newly Sanded Floors or Wood Surfaces:
Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of Absco Quick Dry Polyurethane Primer /Sanding Sealer should be with a #100 to #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the floor with a lint free cloth lightly dampened with mineral spirits. The floor and room temperature should be at least 65°F.

Application:
Apply Absco Quick Dry Polyurethane Primer /Sanding Sealer with the grain of the wood. Apply in well ventilated area by brush, roller, spray, EZ way , or lambswool applicator at room temperature and not in direct sunlight. When using a roller work slowly to avoid air bubbles. Screen the floor or work surface in between coats with any of the following : #150 screen disc, #180 grit sand paper, maroon pad or similar in between coats, or until thoroughly dry. Heavy finish application, high humidity, or lack of air flow will extend drying times. If waiting longer than 24 hours between coats, sanding is recommended.

Drying Time:
When applied according to directions, Absco Quick Dry Polyurethane Primer/Sanding Sealer should be to sand and recoat in 2 hours. Heavy application, high humidity or lack of airflow will extend drying times.

POLYCARE WOOD FLOOR CLEANER

POLYCARE WOOD FLOOR CLEANER
PolyCare Cleaner is the safe effective cleaner for polyurethane coated surfaces. PolyCare is formulated to clean effectively, without leaving any soapy haze or residue on the floor. Ideal for all polyurethane treated, factory pre-finished and laminated residential and commercial/sports floors, as well as cabinets, furniture, railings, counters and woodwork. PolyCare has a unique detergent formula which cleans effectively without rinsing. Light, fresh scented PolyCare leaves only the beauty of fine wood, not a lingering odor and never a residue.

Product Properties
Color: Clear Yellow
VOC :Not Applicable
Freeze Thaw Stability: Stable
Flashpoint: Not Applicable


Directions:
The floor should be swept or vacuumed prior to cleaning for optimum results. Mix PolyCare with warm water at a ratio of 2 ounces per gallon of water. We recommend using a good quality mop, or for large surfaces, several large cotton towels. When using a mop, make sure to ring it out so not to flood the surface with water. Damp mop, rinsing as often as needed. When using towels, soak the towels in the bucket of PolyCare solution. Make sure that they are thoroughly wet. Wring out a towel to remove excess moisture until it is just damp. Wrap the towel around a broom and wipe the floor, going with the grain of the wood, until the floor is completely free of dirt. If spot cleaning is desired, pour the mixed PolyCare solution into a clean spray bottle. Don’t spray the mixture directly on the surface, but on a rag, sponge or towel, before wiping.

Important:
Do not apply PolyCare Cleaner from the bottle directly to the wood surface. Excess liquid may be absorbed by the wood fibers, and may damage or discolor the wood surface. PolyCare has been formulated for use on polyurethane coated surfaces, it is not recommended for use on wax, wax impregnated, or unfinished wood surfaces.

Last-n-Last Absco Polyurethane Wood Floor Finish 350-VOC

Last n Last Absco Polyurethane Wood Floor Finish 350-VOC
ABSCO Professional Polyurethanes offers the latest technology in environmentally compliant wood floor finishes. ABSCO’s high solid content will beautify and protect most commercial and residential wood floors, providing years of enjoyment. ABSCO can also offer superior protection to most interior wood surfaces, such as handrails, trims, furniture and cabinets.

RECOMMENDED USES:
Absco Polyurethane Wood Floor Finish is recommended for most interior commercial and residential wood.

TYPICAL PROPERTIES
Color in Container: Gloss -Clear / Satin – Hazy / Semi-Gloss – Hazy
Solids Content/weight: Gloss – 58+/-2 / Semi-Gloss & Satin – 55+/-2
Chemical Resistance: Excellent
VOC: VOC does not exceed 350 grams/liter
Flash Point: 105°F
Sheen Gloss: No less than 90 units on wood.
Satin: No less than 25-35 units on wood.
Semi-Gloss: 50-60 units on wood.
Matte: 10-20 units on wood
Freeze/Thaw Stability: Stable
Shelf Life: Unlimited in unopened container
Drying Time: 12 hours under good conditions
Cleanup: Mineral Spirits, Paint Thinner, Turpentine
Application Method: Lambs wool applicator, natural bristle brush.
Coverage Approx: 500-600 sq. feet per gallon on raw wood.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:
New or Newly Sanded Floors or Wood Surfaces:Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of Absco Polyurethane Wood Floor Finish and sealer should be a #100 to #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with mineral spirits. Avoid using fillers that contain stearates or wax. The floor or work surface and room temperature should be at least 65°F.

Previously Finished Floors or Wood Surfaces:Remove old finish in poor condition. Screen the floor or work surface with a#100 to #150 screen disc, #180 grit sand paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with mineral spirits. Avoid using fillers that contain stearates or wax. The floor or work surface and room temperature should be at least 65°F.

REMEMBER TO STIR THIS PRODUCT BEFORE AND DURING USE. SATIN AND SEMI-GLOSS CAN BE SHAKEN. AFTER SHAKING, LET IT SIT FOR 10 MINUTES.

APPLICATION:
Apply the finish with the grain of the wood. Apply in well ventilated area by brush, roller, spray, or lambswool applicator at room temperature and not in direct sunlight. When using a roller, work slowly to avoid air bubbles. Screen the floor or work surface in between coats with any of the following #150 screen disc, #180 grit sand paper, maroon pad or similar in between coats. Remember to vacuum and tack thoroughly after screening to remove all dust. Heavy finish application, high humidity or lack of airflow will extend drying times. If waiting longer than 24 hours between coats, sanding is recommended.

APPLICATION OVER STAIN: Absco Polyurethane Wood Floor Finish should adhere well to most stain. If a stain other than Last•n•Last stain is to be used a test for adhesion is recommended. Use Last•n•Last Classic Wood Stain following instruction on label. Allow the stain to dry a minimum of 24 hours under good conditions. Make sure the stain is completely dry before applying the Finish.

DRYING TIME:
When applied according to directions, and in thin coats, Absco Polyurethane Wood Floor Finish should be dry to the touch in 6-8 hour. Allow minimum of 12 hours between coats. Heavy finish application, high humidity or lack of airflow will extend drying times. Absco Polyurethane Wood Finish completely cures within 2 weeks.

CLEAN-UP:
Use paint thinner, mineral spirits or turpentine to clean brushes and applicators.

MAINTENANCE:
Absco Polyurethane Wood Floor Finish never needs waxing. We recommend Polycare Floor Cleaner as the safe and effective cleaning product for all polyurethane coated surfaces. It has a unique soap-free, no rinse formula which will not harm polyurethane or varnished wood surfaces.

Last-n-Last LNL-500X Residential Grade Waterborne Wood Floor Finish

Last-n-Last  LNL-500X  Residential Grade Waterborne Wood Floor Finish
LNL-500X incorporates the latest waterborne technology with Microban antimicrobial protection and a 5 Year Residential Wear Warranty, for advanced protection of wood floors. Our unique technology combines the benefits of professional waterborne floor finishes, with the benefits of Microban antimicrobial protection. Microban protection continuously inhibits the growth of bacteria, mold and mildew that can cause stains, odors, and damage the finish on your floor. And because Microban protection is built into this coating, it will not wash off or wear away for the life of the finish. No Thinning Required.

RECOMMENDED USES:
LNL-500X is recommended for interior residential application.

TYPICAL PROPERTIES
Color in Container: Milky white (dries clear)
Solids Content: 30+/-1%
Chemical Resistance: Excellent
VOC: VOC does not exceed 275 grams/liter
Flash Point: 198°F
Sheen Gloss: >80 units @ 60° on wood
Semi-Gloss: 50-60 units @ 60° on wood
Satin: 25-30 units @ 60° on wood
Freeze/Thaw Stability: Stable (if frozen, thaw completely before using)
Pot Life: Unlimited in unopened container
Dry Time: 2 to 3 hours with good conditions
Clean Up: Water
Application method: T-Bar applicator, Synthetic waterborne applicator and nylon brush.
Coverage: 500-550 sq. feet per gallon.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:
New or Newly Sanded Floors or Wood Surfaces:Prepare the floor according to NWFA or NOFMA accepted standard. Make a final cut with 80-100 grit sandpaper and screen with 120-150 grit screen. Apply LNL-100S or LNL-100SA followed by 2 or 3 coats of LNL-500X. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with water. The floor or work surface and room temperature should be at least 65°F.
Previously finished Floors or Wood Surfaces:Remove old finish in poor condition. If the old finish is shellac or contains wax or any stearate, regardless of the condition, remove it completely then follow surface preparation for New Wood Surfaces. If old finish is still sound and good, screen the work surface with a #150 screen disc, #180 grit sand paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming and wiping the work surface with a lint free cloth lightly dampened with water. The work surface and room temperature should be at least 65°F. Two to three coats work best on previously finished surfaces.

REMEMBER TO STIR THIS PRODUCT BEFORE AND DURING USE. LET IT STAND FOR 10 MINUTES AFTER STIRRING.

Application:
Apply in well ventilated area by nylon brush, or synthetic waterborne applicator at room temperature and not in direct sunlight. Last•n•Last 500X looks milky when applied, but will dry to a clear, beautiful finish. Pou a 6-8” wide line of the finish along the starting wall. Apply the finish with the grain of the wood. Using a clean pre-dampened waterborne applicator, pull forward with the grain of the wood, moving the finish towards the opposite wall. Holding the applicator at a snowplow angle will maintain a wet edge at all times.( Maintain at least 3” wide wet edge to ensure proper coverage). At the end of each run, turn the applicator towards you and pad out the applicator parallel to the wet edge. Feather out turns. If pushed too hard or fast, drips will fly off the applicator. Missed areas can be touched up if seen right away.To prevent lapping and dry marks, be sure you are using the recommendd overage. Do no spread too thin. Screen the work surface in between coats with any of the following #150 screen disc, #180 grit sand paper, maroon pad or similar. Remember to vacuum and tack thoroughly after screening to remove all dust. Allow minimum of two hours between coats, or until thoroughly dry. Heavy finish application, high humidity or lack of airflow will extend drying times. If waiting longer than 24 hours between coats, sanding is recommended.

Application over stain:
Last•n•Last 500X should adhere well to most stain, but a test for adhesion over brands other than Last•n•Last stain is recommended. Use Last•n•Last Classic Wood Stain following instruction on label. Allow the stain to dry a minimum of 24 hours under good conditions. Make sure the stain is completely dry before applying the finish or sealer.

Drying Time:
When applied according to directions, and in thin coats, Last•n•Last 500X should be dry to the touch in 1 hour. Allow a minimum of 2 hours between coats. Heavy finish application, high humidity or lack of airflow will extend drying times.The floor can be walked on after 24 hrs. Last•n•Last 500X cures in approximately 2 weeks. Please allow the finish to be fully cured for area rugs or mats to be put down. The floor is susceptible to scuffing and marring before full cure.

Maintenance:
Last•n•Last 500X never needs waxing. We recommend Polycare Floor Cleaner as the safe and effective cleaning product for all polyurethane coated surfaces. It has a unique soap-free, no rinse formula which will not harm polyurethane or varnished wood surfaces.

Last-n-Last LNL-700A Commercial Grade Oil-n-H20 Wood Floor Finish

Last-n- Last LNL-700A Commercial Grade Oil-n-H20 Wood Floor Finish
LNL-700A incorporates the latest Oil·n·H2O technology with Microban antimicrobial protection, Aluminum Oxide and a 7 Year Residential Wear Warranty, for advanced protection of wood floors. Our unique Oil·n·H2O, 100% urethane technology, is incredibly easy to use, and provides beautiful long lasting protection to all types of interior wood floors. No thinning required. Not recommended for white stained floors. Microban protection continuously inhibits the growth of bacteria, mold and mildew that can cause stains, odors, and damage the finish on your floor. And because Microban protection is built into this coating, it will not wash off or wear away for the life of the finish.

RECOMMENDED USES:
LNL 700A Wood Floor Finish is recommended for interior residential wood.

TYPICAL PROPERTIES
Color in Container: Yellowish white (Dries clear)
Solids Content: 30+/-1%
Chemical Resistance: Excellent
VOC:VOC does not exceed 275grams/liter
Flash Point: 198°F
Sheen Gloss: >80 units @ 60° on wood
Semi-Gloss: 50-60 units @ 60° on wood
Satin: 25-30 units @ 60° on wood
Freeze/Thaw Stability: Stable (if frozen, thaw completely before using)
Shelf Life: Unlimited in unopened container
Dry Time :2 hours under good conditions
Clean Up :Water
Application method: T-Bar applicator, Synthetic waterborne applicator and nylon brush.
Coverage :500-550 sq. feet per gallon.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:
New or Newly Sanded Floors or Wood Surfaces:Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of Last•n•Last 700 and sealer should be a #100 to #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the
floor or work surface with a lint free cloth lightly dampened with water. The floor or work surface and room temperature should be at least 65°F.
Previously Finished Floors or Wood Surfaces:Remove old finish in poor condition. If the old finish is shellac or contains wax or any stearate, regardless of the condition,remove it completely then follow surface preparation for New Wood Surfaces. If old finish is still sound and good, screen the work surface with a #100 to #150 screen disc, #180 grit sand paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming and wiping the work surface with a lint free cloth lightly dampened with water. The work surface and room temperature should be at least 65°F.

REMEMBER TO STIR THIS PRODUCT BEFORE AND DURING USE. LET IT STAND FOR 10 MINUTES AFTER STIRRING.

Application:
Apply in well ventilated area by nylon brush, or synthetic waterborne applicator at room temperature and not in direct sunlight. Slightly dampen applicator with finish prior to starting. Pour finish onto floor in a 4” strip along the starting wall. Apply finish with the grain of the wood. Pull the applicator towards you at a slight “snowplow” angle. Remember to keep a wet edge as you work. Feather all turns and stops in the direction which the applicator was pulled. When you reach the end wall, pull the applicator around in a sweeping motion, without lifting it from the floor. Feather turn, and gently touch any missed spots. Apply at recommended coverage in thin coats.

Application over stain:Last•n•Last 700A should adhere well to most stain, but a test for adhesion over brands other than Last•n•Last stain is recommended. Use Last•n•Last Classic Wood Stain following instruction on label. Allow the stain to dry a minimum of 24 hours under good conditions. Make sure the stain is completely dry before applying the finish or sealer.

Drying Time:
When applied according to directions, and in thin coats, Last•n•Last 700A should be dry to the touch in 1 hour. Allow minimum of 2 hours between coats. Heavy finish application, high humidity or lack of airflow will extend drying times. Last•n•Last 700A completely cures within 2 weeks. Please allow the finish to be fully cured for area rugs or mats to be put down. The floor is susceptible to scuffing and marring before full cure. No more than two coats are recommended per day.

Clean up:
Use water to clean brushes and applicators.

Maintenance:
Last•n•Last 700A never needs waxing. We recommend Polycare Floor Cleaner as the safe and effective cleaning product for all polyurethane coated surfaces. It has a unique soap-free, no rinse formula which will not harm polyurethane or varnished wood surfaces.

Last•n•Last Professional Polyurethane Wood Floor Finish-350 VOC

Last-n-Last Professional Polyurethane Wood Floor Finish-350 VOC

Last•n•Last Professional Polyurethane Wood Floor Finish combines the beauty and durability of 100% pure polyurethane with Microban antimicrobial protection. The Professional’s Choice for over 40 years, Last•n•Last is the premium quality wood finish. Manufactured from the highest quality resins, Last• n• Last will provide years of outstanding beauty and durability on most wood surfaces. Adhesion is excellent – resists flaking and chipping. For interior use only. Not recommended for coating over white surfaces.Last•·n•Last Professional Polyurethane Wood Floor Finish is designed to be used on all types of wood, including floors, stairs, moldings, furniture, and crafts. Microban protection is built into this coating. It will not wash off or wear away for the life of the finish.

RECOMMENDED USES:
Last•·n•·Last Professional Wood Floor Finish is recommended for most interior commercial and residential wood.

TYPICAL PROPERTIES
Color in Container: Gloss - Clear; Satin – Hazy; Semi-Gloss – Hazy
Solids Content/weight: Gloss – 57-60%; Satin – 53%-57%; Semi-Gloss – 53%-57%
Chemical Resistance: Excellent
VOC: VOC does not exceed 350 grams/liter
Flash Point: 105°F
Sheen Gloss: No less than 90 units on wood.
Satin: 25-35 units on wood.
Semi-Gloss: 50-60 units on wood.
Freeze/Thaw Stability Stable
Shelf Life: Unlimited in unopened container.
Drying Time: 4-6 hours under good condition conditions
Cleanup: Mineral Spirits, Paint Thinner, Turpentine.
Application method: Lambswool applicator, natural bristle brush
Coverage Approx: 500-600 sq feet per gallon on raw wood.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:
New or Newly Sanded Floors or Wood Surfaces: Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of Last•n•Last Professional Polyurethane Wood Floor Finish and sealer should be a #100 to #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with mineral spirits. Avoid using filler that contain stearate or wax. The floor or work surface and room temperature should be at least 65°F.
Previously finished Floors or Wood Surfaces: Remove old finish in poor condition. Screen the work surface with a #100 to #150 screen disc, #180 grit sand paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with mineral spirits. . Avoid using filler that contain stearate or wax. The floor or work surface and room temperature should be at least 65°F.

REMEMBER TO STIR THIS PRODUCT BEFORE AND DURING USE. SATIN AND SEMI-GLOSS CAN BE SHAKEN. AFTER SHAKING, LET IT SIT FOR 10 MINUTES.

Application:
Apply the finish with the grain of the wood. Apply in well ventilated area by brush, roller, spray, or lambswool applicator at room temperature and not in direct sunlight. When using a roller, work slowly to avoid air bubbles. Screen the floor or work surface in between coats with any of the following #150 screen disc, #180 grit sand paper, maroon pad or similar in between coats. Remember to vacuum and tack thoroughly after screening to remove all dust. Heavy finish application, high humidity or lack of airflow will extend drying times. If waiting longer than 24 hours between coats, sanding is recommended.

Application over stain:
Last•n•Last Professional Polyurethane Wood Floor Finish should adhere well to most stain, but a test for adhesion over brands other than Last•n•Last stain is recommended. Use Last•n•Last Classic Wood Stain following instruction on label. Allow to dry a minimum of 24 hours under good conditions. Make sure the stain is completely dry before applying the Finish.

Drying time:
When applied according to directions, and in thin coats, Last•·n•·Last Professional Polyurethane Wood Floor Finish should be dry to the touch in 4-6 hours.Allow minimum of 6 hours between coats. Heavy finish application, high humidity or lack of airflow will extend drying times. Last·n·Last Clear Polyurethane Wood Finish completely cures within 2 weeks.

Clean up: Use paint thinner, mineral spirits or turpentine to clean brushes and applicators.

Maintenance:
Last·n·Last Professional Polyurethane Wood Floor Finish never needs waxing. We recommend Polycare Floor Cleaner as the safe and effective cleaning product for all polyurethane coated surfaces. It has a unique soap-free, no rinse formula which will not harm polyurethane or varnished wood surfaces.

Last•n•Last Professional Polyurethane Wood Floor Finish-450 VOC

Last-n-Last Professional Polyurethane Wood Floor Finish-450 VOC

Last•n•Last Professional Polyurethane Wood Floor Finish combines the beauty and durability of 100% pure polyurethane with Microban antimicrobial protection. The Professional’s Choice for over 40 years, Last n Last is the premium quality wood floor finish. Manufactured from the highest quality resins, Last•n •Last will provide years of outstanding beauty and durability on most wood surfaces. Microban protection is built into this coating, it will not wash off or wear away for the life of the finish.

RECOMMENDED USES:
Last•n•Last Professional Polyurethane Wood Floor Finish is recommended for most interior commercial and residential wood.

TYPICAL PROPERTIES
Color in Container: Gloss - Clear ; Satin – Hazy; Semi-Gloss – Hazy
Solids Content/weight: Gloss – 50% ; Satin – 51% ; Semi-Gloss – 51%
Chemical Resistance: Excellent
VOC: VOC does not exceed 450 grams/liter
Flash Point: 105°F
Sheen Gloss: No less than 90 units on wood.
Satin: 25-35 units on wood.
Semi-Gloss: 50-60 units on wood.
Freeze/Thaw Stability: Stable
Shelf Life: Unlimited in unopened container.
Drying Time: 4-6 hrs. under good conditions. The
Cleanup: Mineral Spirits, Paint Thinner, Turpenine.
Application method: Lambswool applicator, natural bristle brush or E-Z Way Applicator.
Coverage Approx: 500-600 sq feet per gallon on raw wood.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:
New or Newly Sanded Floors or Wood Surfaces: Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of Last•n•Last Professional Polyurethane Wood Floor Finish and sealer should be a #100 to #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with mineral spirits. Avoid using filler that may contain stearate or wax. The floor or work surface and room temperature should be at least 65°F.
Previously Finshed Floors or Wood Surfaces: Remove old finish in poor condition. Screen the work surface with a #100 to #150 screen disc, #180 grit sand paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with mineral spirits. Avoid using filler that may contain stearate or wax. The floor or work surface and room temperature should be at least 65°F.

REMEMBER TO STIR THIS PRODUCT BEFORE AND DURING USE. SATIN AND SEMI-GLOSS CAN BE SHAKEN. AFTER SHAKING, LET IT SIT FOR 10 MINUTES.

Application:
Apply the finish with the grain of the wood. Apply in well ventilated area by brush, roller, spray, EZ Way or lambswool applicator at room temperature and not in direct sunlight. When using a roller, work slowly to avoid air bubbles. Screen the floor or work surface in between coats with any of the following #150 screen disc, #180 grit sand paper, maroon pad or similar in between coats. Remember to vacuum and tack thoroughly after screening to remove all dust. Heavy finish application, high humidity or lack of airflow will extend drying times. If waiting longer than 24 hours between coats, sanding is recommended.

Application over stain:
Last•n•Last Polyurethane Wood Floor Finish should adhere well to most stain, but a test for adhesion over brands other than Last•n•Last stain is recommended. Use Last•n•Last Classic Wood Stain following instruction on label. Allow to dry a minimum of 24 hours under good conditions. Make sure the stain is completely dry before applying the Finish.

Drying time:
When applied according to directions, and in thin coats, Last•n•Last Professional Polyurethane Wood Floor Finish should be dry to the touch in 4-6 hours. Allow minimum of 6 hours between coats. Heavy finish application, high humidity or lack of airflow will extend drying times. Last•n•Last Professional Polyurethane Wood Finish completely cures within 2 weeks.

Clean up:
Use paint thinner, mineral spirits or turpentine to clean brushes and applicators.

Maintenance:
Last·n·Last Professional Polyurethane Wood Floor Finish never needs waxing. We recommend Polycare Floor Cleaner as the safe and effective cleaning product for all polyurethane coated surfaces. It has a unique soap-free, no rinse formula which will not harm polyurethane or varnished wood surfaces.